HOME     STORE     BLOG     SCHEMATICS     TUTORIALS     DOWNLOADS     CONTACT

Lithium Ion Battery Charger with Microchip MCP73831
 
Lithium Ion Battery Charger with Microchip MCP73831


 

Lithium Ion Battery Charger with Microchip MCP73831

 


Here's a simple and inexpensive compact lithium ion / polymer battery charger based on Microchip's MCP73831 IC. It features adjustable current charging from 15mA up to 500mA for single cell lipo batteries. With this lipo charger just a few external components are needed. Constant voltage power supply of 5 ~ 6V is needed. Power can also be drawn from USB port. When USB power is 150mA charge current should not be higher. Charge current can be adjusted with external resistors. External LED provides status when lipo battery is fully charged. The LED lights when battery is fully charged. The maximum charging voltage is selectable from 4.2 to 4.5. This has to be chosen at the time of purchase. Typically 4.2V is a standard charging voltage. MCP73831-2 <- 4.2V, MCP73831-3 <- 4.3V, MCP73831-4 <- 4.4V, MCP73831-5 <- 4.5V.


Lithium Ion Battery Charger with Microchip MCP73831

Charging the battery terminal voltage at the start not to be around 4.0V. 5V supply voltage difference is 1V × 500mA = 0.5W maximum heat. If you need a radiator temperature ℃ 20 degrees.
 Dattari 6V power supply, poorly, or if the battery voltage is required because the heat radiator. MCP73831 is very small. Package height is about 1mm. SOT23-5 package. Foot spacing is 0.95mm. The DFN package can be soldered with a soldering iron. Two resistors, two capacitors, LED1 a charger if you have the voltage regulator in addition to the individual.

Schematic of basic use. Experimental breadboard
1100mAH Lithium Polymer battery charging Serubatteripakku 2. RC lithium polymer batteries can be charged for Serubatteripakku a multi-cell charger for cell number, multiply the length times the pin out so that each individual cell.
This instrument is a little difficult to use. The software isn't made.

Charging current measurements. That the use of National Instruments USB-6008.
First degree battery voltage 3.7V, 4V after power-on and then took 40 minutes to reach 4.2V. The charge current is 4.2V charging voltage go down a little bit before. Down at approximately 50mA charging current charges to the extent not completed. 1C (1000mAH battery if the charging current of 1000mA to mean) are fully charged battery charge takes about 1.5 hours.

15mA ~ 500mA charge current of the charger circuit diagram can be changed with reference to Rotaridippusuitchi.
 • The green LED lights and power.
 - Charge current set Rotaridippusuitchi.
 - Connecting the battery and the red LED lights.
 - Red LED is off when fully charged.
Rotaridippusuitchi positive logic for setting the charge current (also known as real code) to use the thing.

The charge current of the circuit
The charge current is determined by:
 Charge Current [mA] = 1000 ÷ PROG pin lead to resistance [kΩ]
Attach a worksheet to keep the calculation of the resistance of the circuit are summarized in the following


Lithium Ion Battery Charger with Microchip MCP73831


Lithium Ion Battery Charger with Microchip MCP73831


Lithium Ion Battery Charger with Microchip MCP73831

Lithium Ion Battery Charger with Microchip MCP73831

Lithium Ion Battery Charger with Microchip MCP73831

Lithium Ion Battery Charger with Microchip MCP73831

Lithium Ion Battery Charger with Microchip MCP73831

Lithium Ion Battery Charger with Microchip MCP73831





Accurate LC Meter Capacitance Inductance Meter with 16F628 and LCD
Volt Ampere Meter with 16F876 Microcontroller and LCD display
 
Accurate LC Meter

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings.
PIC Volt Ampere Meter

Volt Ampere Meter measures voltage of 0-70V or 0-500V with 100mV resolution and current consumption 0-10A or more with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with 16x2 backlighted LCD.

50MHz 60MHz Frequency Meter / Counter with 16F628 & LCD
1Hz - 2MHz XR2206 Function Generator
60MHz Frequency Meter / Counter

Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.
1Hz - 2MHz XR2206 Function Generator

1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

BA1404 HI-FI Stereo FM Transmitter
USB IO Board PIC18F2455 / PIC18F2550
BA1404 HI-FI Stereo FM Transmitter

Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter broadcasts high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
USB IO Board

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible.

ESR Meter / Transistor Tester Kit
Audiophile Headphone Amplifier Kit
 
ESR Meter / Capacitance / Inductance / Transistor Tester Kit

ESR Meter kit is an amazing multimeter that measures ESR values, capacitance (100pF - 20,000uF), inductance, resistance (0.1 Ohm - 20 MOhm), tests many different types of transistors such as NPN, PNP, FETs, MOSFETs, Thyristors, SCRs, Triacs and many types of diodes. It also analyzes transistor's characteristics such as voltage and gain. It is an irreplaceable tool for troubleshooting and repairing electronic equipment by determining performance and health of electrolytic capacitors. Unlike other ESR Meters that only measure ESR value this one measures capacitor's ESR value as well as its capacitance all at the same time.
Audiophile Headphone Amplifier Kit

Audiophile headphone amplifier kit includes high quality audio grade components such as Burr Brown OPA2134 opamp, ALPS volume control potentiometer, Ti TLE2426 rail splitter, Ultra-Low ESR 220uF/25V Panasonic FM filtering capacitors, High quality WIMA input and decoupling capacitors and Vishay Dale resistors. 8-DIP machined IC socket allows to swap OPA2134 with many other dual opamp chips such as OPA2132, OPA2227, OPA2228, dual OPA132, OPA627, etc. Headphone amplifier is small enough to fit in Altoids tin box, and thanks to low power consumption may be supplied from a single 9V battery.
 

Arduino Prototype Kit
RF Remote Control 433MHz Four Channel
 
Arduino Prototype Kit

Arduino Prototype is a spectacular development board fully compatible with Arduino Pro. It's breadboard compatible so it can be plugged into a breadboard for quick prototyping, and it has VCC & GND power pins available on both sides of PCB. It's small, power efficient, yet customizable through onboard 2 x 7 perfboard that can be used for connecting various sensors and connectors. Arduino Prototype uses all standard through-hole components for easy construction, two of which are hidden underneath IC socket. Board features 28-PIN DIP IC socket, user replaceable ATmega328 microcontroller flashed with Arduino bootloader, 16MHz crystal resonator and a reset switch. It has 14 digital input/output pins (0-13) of which 6 can be used as PWM outputs and 6 analog inputs (A0-A5). Arduino sketches are uploaded through any USB-Serial adapter connected to 6-PIN ICSP female header. Board is supplied by 2-5V voltage and may be powered by a battery such as Lithium Ion cell, two AA cells, external power supply or USB power adapter.
200m 4-Channel 433MHz Wireless RF Remote Control

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
 

Electronics-DIY.com © 2002-2024. All Rights Reserved.